LaBella's Enterprises & LaBella's HHO Dry Cell Kits & Accessories Hydrogen Dry Cell HHO Generator Kits & Accessories Hydrogen Facts Testimonials From Real People It's GUARANTEED To Reduce Your Fuel Consumption Burn Water For Fuel (Hydrogen) And Get A Tax Refund From The IRS

Convert your vehicle to a water (hydrogen HHO) hybrid with the very latest HHO dry cell kits, hydrogen generator kits, supplemental hydrogen generators kits, hydrogen on demand kits and possibly increase your fuel mileage up to double of what you are getting now. Furthermore, the IRS will give you a tax refund for doing so.

Hydrogen development is not a new technology, it's been around since the 1800's. Now with skyrocketing fuel prices, you can drive around using WATER AS FUEL and LAUGH at RISING GAS COSTS, while at the same time REDUCE emissions and help PREVENT GLOBAL WARMING?

Here is the truth. There is a way to permanently save money at the pump. The solution is very simple, economical and environmentally friendly. Hydrogen dry cell generators are the very latest in supplemental hydrogen. Don't let the term "DRY" fool you, it's not literal. The dry cell generator receives electrolyte from the bubbler tank reservoir by means of gravity feed. Once the electrolyte fluid enters the dry cell generator, it forces the hydrogen back up and into the bubbler tank reservoir located above it where it is then pulled into the engine's intake system via 3/8 elbow fitting and a 3/8 ID clear hose located at the very top of the bubbler tank reservoir. All of this is accomplished WITHOUT the use of any pump. Unlike other hydrogen generators that bath the plates in the same hot container, dry cell generators separate the electrolyte container from the dry cell generator, making it run cooler and more efficiently with less amperage draw on your charging system. These units are very compact and fit where others cannot. See illustration below.

PRO 1 HHO Dry Cell Generator: Don't let the small size fool you. The Pro series dry cell generator out performs other dry cell generator 3 times its size and it fits where other cannot. This is the new generation of supplemental hydrogen development. In the world of supplemental hydrogen, be careful of the highest output generators and those that brag about them, because it's not always how much a HHO generator produces in LPM (liters per minute) but how the computer is PROPERLY tuned so the hydrogen can be best burned (supplemented). Furthermore, and most importantly, there is no such thing as a kit that is complete and that fits all vehicles. WHY? Because each vehicle's computer system and components are different and present different lean out procedures to KEEP the computer in the lean position without it undoing itself once performed. See instructions we provide under "You Must Fool The Computer" CLICK (Please read all the info therein). Our generators have been tested on big V8 engines and in all cases when installed properly, get a minimum of 5 extra miles per gallon of fuel, more on smaller engines. For more mileage on larger V8 engines and diesels, the Pro 2 Twin kit is the right choice. Hydrogen (HHO) is a very powerful, clean burning fuel– in fact it is the cleanest and cheapest form of fuel– taken from water (H2O). You've seen it on the space shuttle rockets developed by NASA: the bright-blue flames coming off the side rockets. Hydrogen can burn a hole clean through cylinder pistons and burn up cylinder heads if too much hydrogen is deployed into the engine's intake manifold and/or if the vehicle's computer is not leaned out properly. You can trust the PRO 1 Dry Hydrogen Generator to meet your expectancy, and we will see to it that it does. We provide tech support and good communication as you install your unit. We have access to all US domestic & import makes and models and can tell you, once a purchase is made, what specifics you need to address to get the very most out of your PRO 1 Hydrogen Generator. Supplemental hydrogen is not only good for your wallet, it improves the environment through low emissions. How low? The IRS will give you money for putting it on your vehicle and protecting the air we breath. NO JOKE! Read how: CLICK. 

Don't Be Taken By Cheap Knockoffs or Look-A-Likes:
So you've found a great HHO hydrogen generator kit bargain on the internet. A price you cannot believe for a similar hydrogen generator kit or product that cost twice as much. Be cautious of those who sell HHO generator kits and products but have no real established business or cannot provide genuine technical support after the purchase. Especially those out of the USA. Everybody sees a quick buck in this business: Making HHO systems in their backyard or garage with the use of every conceivable hardware material from Home Depot or your kitchen. These businesses, if you want to call them that, could be here today but gone tomorrow. Cheap imports from China and around the world are popping up all over the place. Look-a-like knockoffs that have no real quality and promises of outrageous HHO liter production are regularly advertised on the web. Here's a test you can make by just looking at some of the dry cell units out there. Take a good look at the side plates. These are usually made of acrylic materials or Plexiglas construction. If these are thinner than a 1/2 inch, you are in for some real leaky trouble. Why? Because the end plates will warp with minimal heat. Also, be careful of those that like using end plates that are not transparent. Why? Because they may not want you to know what is happening inside the cell plates after minimal use. Our products are tested and proven on real vehicles and the products we purchase are from well-established companies that have been around for years before HHO had become popular. Here's a real-life example that cost me thousands of dollars before I caught on to the the get-rich schemes of some HHO companies. I purchased a very expensive stainless steel HHO generator kit that sold for three times the amount you regularly see on the internet, thinking this must be the best. They boasted of great support with phone numbers. The unit was a wet cell system that came with all of the electronic trick outs needed to yield the very best miles per gallon. Here's what I got: a stainless steel container that was not the one that I paid for (one of less HHO production & size), no ScanGauge that I also paid extra for, support phone numbers that became unanswered and were constantly changed, a unit that used a very harsh electrolyte mix that was not really needed, cheap electrical fuse holders that overheated and lost connection within a week's time. And besides this, here's what I found out the hard way about wet cell HHO generators that have electrical wires entering the container where the electrolyte is stored. Electrolyte is a corrosive chemical- an acid to be direct. One that will eventually eat up metal components sooner or later. So, if you place copper wires inside of a corrosive environment like an electrolyte bath, guess what happens to the electrical wiring and connections? That's right, it corrodes and loses connection. Case in point: the same process happens to those that dunk their boat trailers into saltwater while the trailer wiring is still connected to voltage. Eventually wire connections become corroded, evidenced by turning the once bright copper wiring into high resistant, black-looking wire strands that cause all sorts of malfunctioning electrical problems. Dry cell generators virtually eliminate this problem because the wire connections are made outside the electrolyte solution. The bottom-line here is, when you consider purchasing an HHO generator system or kit, take it from those that spent the money and did their homework, dry hydrogen generator systems are the better choice, only if they come from an established, reputable company. Read more important information BEFORE you make a purchase only to find out there's no technical support. Our installation manual: CLICK

 SEE PROOF That HHO DRY Cells WORK

Click Image To Enlarge Pro 1 HHO Dry Cell Generator  $106.00 + shipping Shipping US Postal Priority 2-3 day Installation Instructions click Out of USA Need to Contact Us  For Shipping Price Measures only 4" X 4" X 2" and puts out 2.25 Liters of HHO Gas per minute with no overheating, results up to V10 Out performs other dry cell generators three times its size and fits where others cannot. See videos Click Assembled as shown. 9 plates ( -nnn+nnn- ) The plates are 3.5" x 3.5" 18 gauge 316L stainless The Acrylic is 4"x 4"x 1/2" thickness The 2 hose barbs are 3/8" The attachment bracket is made from 1/16" x 3/4" aluminum angle. Comes with 2 1/4-20 wing nuts for easy connection to your power source 316L surgical stainless steel plates Design keeps the current between the plates producing more hydrogen with less heat. Current flows thru the plates making a more efficient cell. Tank-less dry cell generator are the only way to achieve this Studded connections- no wires to corrode from electrolyte Easiest to install	Click Image To Enlarge Pro 1 HHO Dry Cell Generator Kit Basic 2 Qt. Tank $134.36 + shipping Shipping US Postal Priority 2-3 day Installation Instructions click Out of USA Need to Contact Us  For Shipping Price This kit is suitable for V8 or smaller diesel, carbureted, and generator/small engines non-computerized. Note: For mileage gain the following applicable enhancers listed below will be needed in addition to this kit: Vehicles 1995 and older with fuel injection and 2 or less oxygen sensors, and 5v map sensor will need to contact us for an EFIE. OBDII systems 1996 and newer need the “Volo VP12 Computer Chip EFIE for OBDII Systems.” Read the description of the aforementioned enhancers listed below. Diesel engine applicatons need no EFIE Pro 1 Hydrogen Dry Cell Measures only 4" X 4" X 2" and puts out 2.25 Liters of HHO Gas per minute with no overheating, results up to V10 Design keeps the current between the plates producing more hydrogen with less heat. Current flows thru the plates making a more efficient cell. Tank-less dry cell generators are the only way to achieve this (see further specs under Pro 1  HHO Dry Cell Generator ) 2 quart tank bubbler with molded bracket & hose fittings for electrolyte  measures 8.63" L x 4.25" W x 5.26" Hgt. (2.25" Neck) 10 ft. of 3/8 ID clear hose Add on pulse width modulator and/or proper enhancer enhancer for best performance; see details on these items listed below Online instructions included with support
Click Image To Enlarge Pro 2 TWIN HHO Dry Cell Generator Kit SUPER COMPLETE 4 Qt. Tank PRO 2 with 40 AMP PWM $286.38 and Up Depending on Optional Choices: VP12 Enhancer and/or Vaporizer Trap + shipping Shipping US Postal Priority 2-3 day weight average 9 lbs. Installation Instructions click Out of USA Need to Contact Us  For Shipping Price   This kit is suitable for V10 or smaller diesel, carbureted, and generator/small engines non-computerized. Note: For mileage gain the following applicable enhancers listed below will be needed in addition to this kit: Vehicles 1995 and older with fuel injection and 2 or less oxygen sensors, and 5v map sensor will need to contact us for an EFIE. OBDII systems 1996 and newer need the “Volo VP12 Computer Chip EFIE for OBDII Systems.” Read the description of the aforementioned enhancers listed below. Diesel engine applicatons need no EFIE 2 twin Pro 1 Hydrogen Dry Measures only 4" X 4" X 2" and puts out 2.25 Liters of HHO Gas per minute with no overheating, results up to V10 Both cells are assembled 9 plates ( -nnn+nnn- ) The plates are 3.5" x 3.5" 18 gauge 316L stainless assembled as shown. 9 plates ( -nnn+nnn- ) The plates are 3.5" x 3.5" 18 gauge 316L stainless Design keeps the current between the plates producing more hydrogen with less heat. Current flows thru the plates making a more efficient cell. Tank-less dry cell generators are the only way to achieve this 4 qt high capacity tank bubbler with molded bracket & hose fittings for electrolyte (check under hood clearance before purchase- tank measures 8.63" L x 4.17" W x 9.84" Hgt. (2.25" Neck) with molded bracket & hose fittings. Optional 2 qt tank upon request 10 ft. of 3/8 ID clear hose 10 ft of 12 ga black wire, 10 ft. 12 ga. red wire 40 Amp Pulse Width Modulator (appearance may vary) 40 amp relay and wire harness 12v On/Off toggle switch  Various wire terminal connectors 50 amp meter internal shunt 3/8 elbow fitting for output hose connection at intake duct 30 amp inline fuse holder and fuse Backfire check valve Online instructions included with support For additional options for this kit, use the dropdown arrow below to chose them Pro 2 SC Kit + shipping. Click The Dropdown Arrow To Chose Additional Options Pro 2 SC Kit Basic Without Options $286.38 USD Pro 2 SC Kit w/ VP12 Chip & Vaporizer $401.88 USD Pro 2 SC Kit w/ VP12 Chip $392.38 USD Pro 2 SC Kit w/Vaporizer $295.80 USD	Click Image To Enlarge Pro 1 HHO Dry Cell Generator Kit SUPER COMPLETE 2 Qt. Tank PRO 1 with 40 AMP PWM $174.18 and Up Depending on Optional Choices: VP12 Enhancer and/or Vaporizer Trap + shipping Shipping US Postal Priority 2-3 day weight average 6 lbs. Installation Instructions click Out of USA Need to Contact Us  For Shipping Price     This kit is suitable for V8 or smaller diesel, carbureted, and generator/small engines non-computerized. Note: For mileage gain the following applicable enhancers listed below will be needed in addition to this kit: Vehicles 1995 and older with fuel injection and 2 or less oxygen sensors, and 5v map sensor will need to contact us for an EFIE. OBDII systems 1996 and newer need the “Volo VP12 Computer Chip EFIE for OBDII Systems.” Read the description of the aforementioned enhancers listed below. Diesel engine applicatons need no EFIE Pro 1 Hydrogen Dry Measures only 4" X 4" X 2" and puts out 2.25 Liters of HHO Gas per minute with no overheating, results up to V10 Assembled 9 plates ( -nnn+nnn- ) The plates are 3.5" x 3.5" 18 gauge 316L stainless Design keeps the current between the plates producing more hydrogen with less heat. Current flows thru the plates making a more efficient cell. Tank-less dry cell generators are the only way to achieve this 2 quart tank bubbler  measures 8.63" L x 4.25" W x 5.26" Hgt. (2.25" Neck) with molded bracket & hose fittings. Optional 4 qt tank upon request (ck your under check under hood clearance before purchase- tank size: measures 9.842” x 8.632” x 4.173” 10 ft. of 3/8 ID clear hose 10 ft of 12 ga black wire  10 ft. 12 ga. red wire 40 Amp Pulse Width Modulator (appearance may vary) 40 amp relay and wire connector/harness 12v On/Off toggle switch  Various wire terminal connectors 50 amp meter internal shunt 3/8 elbow fitting for output hose connection at intake duct 30 amp inline fuse holder and fuse Backfire check valve Online instructions included with support For additional options for this kit, use the dropdown arrow below to chose them Pro 1 SC Kit + shipping. Click The Dropdown Arrow To Chose Additional Options Pro 1 SC Kit Basic Without Options $174.18 USD Pro 1SC Kit w/ Vaporizer/Bubbler $183.68 USD Pro1 SC Kit w/ VP12 chip $294.18 USD Pro1 SC Kit w/ VP12 chip & Vaporizer $303.68 USD
Click Image To Enlarge 2 Quart Bubbler Tank  For HHO Dry Cell Generator   $29.99 + shipping Shipping US Postal Priority 2-3 day Installation Instructions click Out of USA Need to Contact Us  For Shipping Price 2 Quart Tank  measures 8.63" L x 4.25" W x 5.26" Hgt. (2.25" Neck) with molded bracket & hose fittings Tank Comes with (3) 3/8" Barbed fittings Comes with tight fitting lid--non vented Connects to HHO dry cell fittings Tank is guaranteed not to leak Allows the water to circulate in the generator through the tank, makes for a cooling running system and lower amp draw Click Image To Enlarge 4 Quart Bubbler Tank For HHO Dry Cell Generator $29.99 + shipping Shipping US Postal Priority 2-3 day Installation Instructions click Out of USA Need to Contact Us  For Shipping Price 4 Quart Tank  measures 8.63" L x 4.17" W x 9.84" Hgt. (2.25" Neck)with molded bracket & hose fittings Tight fitting cap-non vented High capacity tank for for more electrolyte and less servicing if room under hood accommodates Connects to HHO dry cell fittings Tank is guaranteed not to leak Click Image To Enlarge Vaporizer  Bubbler Scrubber Trap $9.50 + shipping Installation Instructions click Out of USA Need to Contact Us  For Shipping Price Keeps electrolyte from entering the engine's intake manifold which can trigger the check engine light or cause engine damage due to cylinder washout Some call this device a scrubber because it keeps the HHO output line free of build up that would normally occur without it Measurers 9 1/2 inches tall, made of 1 1/2 inch PVC pipe with 3/8  elbow fittings top and bottom Can be tie strapped to most any accessible area like the side of the bubbler tank and away from high heat like exhaust manifolds Recommended to be use with our HHO Foam B Gone product Goes between the hydrogen generator HHO output hose Electrolyte that enters the vaporizer condenser under extended use will need to be drained All fittings need to be sealed with  Goop glue upon assembly See installation instructions Click	Click Image To Enlarge Pro 2 TWIN HHO Dry Cell Generator Kit 4 Qt. Tank Basic $246.56 + shipping Shipping US Postal Priority 2-3 day weight average 7.5 lbs. Installation Instructions click Out of USA Need to Contact Us  For Shipping Price This kit is suitable for V10 or smaller diesel, carbureted, and generator/small engines non-computerized. Note: For mileage gain the following applicable enhancers listed below will be needed in addition to this kit: Vehicles 1995 and older with fuel injection and 2 or less oxygen sensors, and 5v map sensor will need to contact us for an EFIE. OBDII systems 1996 and newer need the “Volo VP12 Computer Chip EFIE for OBDII Systems.” Read the description of the aforementioned enhancers listed below. Diesel engine applicatons need no EFIE 2 (double) Pro 1 Hydrogen Dry Cells Measures only 4" X 4" X 2" ea. and puts out 2.25 Liters of HHO Gas per minute with no overheating, results up to V10 Design keeps the current between the plates producing more hydrogen with less heat. Current flows thru the plates making a more efficient cell. Tank-less dry cell generators are the only way to achieve this  4 quart tank bubbler measures 8.63" L x 4.17" W x 9.84" Hgt. (2.25" Neck) with molded bracket & hose fittings 10 ft. of 3/8 ID clear hose Online instructions included with support      HHO Hydrogen Generator Accessories STARTER KIT $70.00 and UP Depending on Optional Choices: VP12 Enhancer and/or Vaporizer Trap, 2 or 4 qt tank + shipping  Shipping US Postal Priority 2-3 day Installation Instructions click Out of USA Need to Contact Us  For Shipping Price DOES NOT INCLUDE Hydrogen Generator HHO Dry Cell, Includes 40 Amp PWM Pulse Width Modulator and optional Volo Chip EFIE YOU Provide Your Own Favorite Hydrogen Generator This is the kit you need if you HAVE YOUR OWN 12 volt DC HHO DRY CELL or Hydrogen Generator and if the application is for 1996 and newer vehicle, choose optional Volo Chip enhancer for mileage gain Choose optional 2qt or 4qt capacity tank bubbler with molded bracket & hose fittings for electrolyte (see tank sizes specs for appropriate size tank on this page 10 ft. of 3/8 ID clear hose 10 ft of 12 ga black wire, 10 ft. 12 ga. red wire 40 Amp Pulse Width Modulator preassembled and ready to install w/ terminal connectors.(may vary in appearance) DON’T BE FOOLED...IT'S VIRTUALLY IMPOSSIBLE TO MAINTAIN A STABLE AMP DRAW WITHOUT IT 40 amp relay and wire harness 12v On/Off toggle switch  50 amp meter internal shunt 3/8 elbow fitting for output hose connection at intake duct 30 amp inline fuse holder and fuse Inline backfire check valve Online instructions included with support Note: For mileage gain vehicles 1995 and older with fuel injection and 2 or less oxygen sensors, and 5v map sensor will need to contact us for an EFIE. OBDII systems 1996 and newer need the “Volo VP12 Computer Chip EFIE for OBDII Systems.” Read the description of the aforementioned enhancers listed below. Diesel engine applicatons need no EFIE For additional options for this kit, use the dropdown arrow below to chose them HHO Starter Kit. Click The Dropdown Arrow To Chose Additional Options 4 Qt Starter Kit Basic Without Options $80.00 USD 2 Qt Starter Kit Basic Without Options $70.00 USD 4 Qt Starter Kit & Volo Chip $184.38 USD 2 Qt Starter Kit & Volo Chip $174.38 USD 2 Qt Starter Kit & Volo Chip & Vaporizer $183.88 USD 4 Qt Starter Kit & Volo Chip & Vaporizer $193.88 USD 4 Qt Starter Kit & Vaporizer $89.50 USD 2 Qt Starter Kit & Vaporizer $79.50 USD
	Click Image To Enlarge 40 Amp Pulse Width Modulator PWM (appearance may vary) w/ Accessories For Hydrogen Generator $59.00 + shipping Installation Instructions click Out of USA Need to Contact Us  For Shipping Price This is a fully assembled 40 amp PWM (appearance may vary) and optional accessories ready to install as seen in picture above, especially for HHO generator systems Includes all of the items shown for a complete hydrogen generator cell hookup: 50 amp meter internal shunt, 30 amp fuse holder & fuse, 30/40 amp relay w/ connector plug, on/off toggle switch, terminal connectors An absolute must for hydrogen production efficiency and control of amperage draw for a cooler running HHO generator Produces better HHO production by changing the voltage wave form See installation instructions: Connecting the Power Source Click
Click Images To Enlarge 10/20/30/40/50 Amp Meter DC Panel Meter-No Shunt Needed $20.00 + shipping  Installation Instructions click Out of USA Need to Contact Us  For Shipping Price This is a 0-50 amp meter DC class 2.5 for HHO use and other device applications using 12 volts Internal shunt, connects in series or inline on the ground side of the load Comes with mounting lugs and nuts Perfect for monitoring HHO generators within the proper amp draw See dimensions above second illustration Always adjust amp draw when device is in the fully warm It's best to use an amp meter that is rated above the device's highest amp draw to prevent meter burnout Damage to meter due to improper use voids warranty and shipping fees are the responsibility of the buyer in all cases. Installation should be performed by persons familiar with DC voltage applications	Click Images To Enlarge Heavy Duty Positive Sealing Bubbler Tank Cap $6.95 + shipping Out of USA Need to Contact Us  For Shipping Price Increases your HHO production (LPM) and your safety by eliminating hydrogen gas loss through leaky caps New and improved heavy duty NON-VENTED bubbler tank cap with stationary locked-in rubber sealing gasket Suitable for ALL dry cell generator  applications that require NON-Venting bubbler tanks Fits 2 ¼ inch threaded neck openings Easy to grip and guaranteed not to crack under normal use
Click Images To Enlarge Volo VP12 Computer Chip EFIE for OBDII Systems Must Be A Common to USA Make Vehicle Requires driving 100 miles before it adapts to the computer system or it can be programmed specific by providing year, make, model, engine, upon ordering $106.00 + shipping Out of USA Need to Contact Us  For Shipping Price Takes care of leaning ALL computer sensors for HHO specific use with one enhancer (EFIE) chip Like with any of the other Volo chips this cannot be used if any other enhancers or tuners are on the engine-it must be removed or deactivated The chip will adapt to the vehicle's computer system after driving 100 miles. Must be OBDII computer system, vehicles from 1996 common to USA makes The VP12 is a 20MHz Microcontroller. It utilizes its high speed serial input/output to communicate directly with the ECU through the OBD-II port wiring When using HHO as a fuel supplement, the chip will adjust fuel delivery and timing to optimize efficiency Recommended modifications : K&N or equivalent non-restrictive intake combined with a (Oxyhydrogen) hydrogen generator system for optimum mileage and performance Compatible with factory equipped Turbo/Superchargers, diesel engines, Flex-Fuel, & HHO supplemental hydrogen generator applications. It is NOT compatible with hybrid engine options, propane, or natural-gas The VP12 comes with 4 tap-in connectors which you connect to 4 wires behind the face of the vehicles OBDII (DLC) Data Link Connector port. Instructions are included on which wires to connect to. Not a cheap scam chip like many online. Search online reviews of this product   Click Images To Enlarge  HHO 40 Amp PWM Pulse Width Modulator For HHO Hydrogen Generator HHO DRY CELL KITS $18.00 free shipping Out of USA Need to Contact Us For Shipping Price PWM SPECS (item may vary in appearance. Knob may be shipped inside enclosure) TECHNICAL SPECIFICATIONS: Pulse width modulator is air cooled; no fan needed Power Requirement DC 10-50 V Rated Current 40 A (Maximum Output Current) Frequency 12000 Hz Control Motor Power 0.01-2000 W 12 V: 480 W (max), 24 V: 960 W (max) 36 V: 1440 W (max), 50 V: 2000 W (max) Regulation Range 5-100% PCB Size 90 x 51 mm (inch: 3.5" x 2") Case Size 105 x 55 x 40 mm (inch: 4" x 2.2" x 1.6") Weight 130 g See instructions in the Hydrogen Dry Cell Manual top left of any page in the navigation menu. A DC ammeter is recommenced to be used with this controller. Do NOT mount near high heat or water prone areas or remove control knob once installed PWM requires assembling: Pry open case with small screw driver, remove any packing, do not remove knob once installed or circuit board may become damaged, you may cut the back to accommodate wiring. IMPORTANT warranty information: All PWM's are pretested. Damage to controller due to improper connections voids warranty. Installation should be performed by persons familiar with DC voltage applications	Click Images To Enlarge HHO Foam B Gone HHO Anti Foam Agent $9.95 Free shipping Out of USA Need to Contact Us  For Shipping Price Foaming in the bubbler tank, a natural occurrence in supplemental hydrogen generator systems, can cause major problems if the electrolyte bubbles enter the HHO output hose to the engine's intake Before now, there was little remedy for this issue which caused, among other engine related issues, throttle body throat corrosion and sticking, causing computer code generation, engine killing and/or no engine acceleration HHO Foam B Gone, HHO anti foam agent solution, resolves this problem with only one drop from the applicator into the bubbler tank's electrolyte solution-instantly In drive-by wire engine applications, engine's that do not employ an accelerator cable to move the throttle throat flap, are most affected by HHO electrolyte contamination that can damage the costly throttle body assembly To reduce the possibility of this type of damage to your engine, its best to incorporate a vaporizer bubbler trap coupled with the use of HHO Foam B Gone, HHO anti foam agent Use of the HHO anti foam agent causes no know problems with the system nor it's production and the solution need not be reapplied as long as the bubbles do not reoccur  The 2 oz. bottle can last for several years and is priceless insurance in a bottle     Click Images To Enlarge HHO Hydrogen Generator Oxygen Sensor and Map Enhancer EFIE Controller OUT OF STOCK Contact Us for Recommended EFIE For 1995 and Older Vehicles Engines w/ Fuel Injection $36.04 + shipping Out of USA Need to Contact Us For Shipping Price For 95 & Older Fuel Injected Vehicles W/O2 Sensors Controls Oxygen Sensors And One 5v Map Sensor Not For OBDII Systems Or Carbureted Engines Full step by step instructions for installation. May be used on 1996 and newer OBDII system that have fuel injection with map sensor and two or less O2 sensors The device is also compatible on some later models with 2 or less oxygen sensors, and 5v map sensor. It's not compatible for AFR sensors or 1996 and newer Fords with frequency map sensor
*US Priority Shipping	READ DISCLAIMER